Electrolux washing machine error codes

What do the strange symbols mean on the display of an Electrolux automatic washing machine? Most often these are indications of certain errors. Knowing the error codes of Electrolux washing machines, we will be able to quickly find the faulty unit or eliminate this or that breakdown. In addition, error codes for Electrolux washing machines will help you deal with emergency situations.

We put all the codes in a small table, with which you can quickly diagnose your washing machine. But as practice shows, there are no errors in this table. For example, the EH0 error in the Electrolux washing machine indicates a low mains voltage, but this code is not in the tables for services.

Electrolux washing machine error table

The code	Description of the problem	Possible causes
E11	No water supply during washing or insufficient water level for the maximum set time	The solenoid valves and control triacs are checked (the resistance of the valve windings is about 3.75 kOhm); Insufficient water pressure; Clogged intake pipes.
E13	Water in the tray	The reasons for the presence of water in the pan are checked.
E21	Water does not drain. The maximum waiting time is 10 minutes.	The intake system is checked; The drain pump is checked - the nominal resistance of its windings should be about 170 Ohms; The control module needs to be checked.
E23	Drain pump triac failure	The control module needs to be repaired.
E24	Drain Pump Triac Circuit Malfunction	The circuit is checked.
E31	Pressure sensor failure	The pressure sensor is checked; Electrical circuits are monitored.
E32	Pressure sensor calibration error	The sensor may be incorrectly calibrated within 0-66 mm. The following works are carried out (If necessary, damaged units are replaced): Checking the filling valve; Filter cleaning; Checking the availability of water supply; Checking the pressure switch tube; Checking the operation of the pressure sensor.
E33	Inconsistent operation of the heating element protection sensor and the first level sensor	The performance of these sensors is checked; The condition of the level sensors and the pressure sampling chamber is checked; The voltage in the outlet is checked (it may be too high); Check for leakage on the heating element (ohmmeter)
E34	Error between anti-boil level-2 and pressure switch	Pressure sensors are checked; Electrical circuits are checked; The pressure switch tube is checked and replaced.
E35	High water level in the tank	The overflow level switch has opened, this happens when machine pouring water. The correct operation of the pressure switch should be checked.
E36	Failure of the heating element protection sensor (ABS)	The sensor is being tested for functionality.
E37	Failure of the sensor of the first water level (L1 S)	The sensor is being tested for functionality.
E38	Clogged pressure switch tube	The pressure switch tube is being cleaned.
E39	Overflow sensor failure	The sensor is being tested for functionality.
E3A	TENA relay failure	The electronic unit needs to be replaced.
E41	Sunroof not closed	The tightness of the closing of the loading hatch is checked.
E42	Sunroof lock malfunction	Door lock needs to be checked.
E43	Breakdown of the hatch lock triac	The triac is being checked and replaced.
E44	Loading hatch closing sensor failure	It is necessary to check the functionality of the sensor.
E45	Breakage of the hatch lock triac control circuit	The operation of electrical circuits is checked.
E51	Short circuit of the triac of the drive motor	The performance of the triac is checked.
E52	No signal from the tachogenerator of the drive motor	The position of the sensor coil is checked; Checking the functionality of the sensor.
E53	Breakage of the control circuits of the triac of the drive motor	The triac is being checked and replaced (on the electronic control module).
E54	Malfunction of one of the contact groups of the motor reverse relay	The relay is checked and replaced.
E55	Break in the power supply circuit of the drive motor	The supply circuits are checked and the wires are replaced.
E56	No signals from the tachogenerator for 15 minutes	The tachogenerator is checked and replaced.
E57	Exceeded current strength over 15 A	It is necessary to check the drive motor and all supply circuits.
E58	Current in the drive motor is greater than 4.5 A	It is necessary to check the drive motor and all supply circuits; The control module is being tested.
E59	No tachogenerator signal when a signal is given to change the engine speed (other than zero)	Engine and electrical circuits need to be checked; The tachogenerator is checked; The functionality of the electronic module is checked.
E5A	The temperature of the cooling radiator is exceeded - above +88 degrees	The electronic module needs to be checked and replaced.
E5C	Exceeded voltage in the DC bus (above 430 Volts)	The electronic module needs to be checked and replaced.
E5D	Inability to receive and send FCV messages for 2 seconds	The electronic module needs to be checked and replaced.
E5E	No communication between main board and FCV board	The electronic module needs to be checked and replaced.
E5F	Repeated FCV board resets and continuous configuration requests	It is necessary to check and replace the electronic module; The integrity of the circuits is checked.
E61	Insufficient water heating for a certain time	The code is displayed only in diagnostic mode.TENA check required.
E62	Water heating above +88 degrees in 5 minutes	The resistance of the temperature sensor is checked in a cooled state (nominal in the range of 5.7-6.3 kOhm); The heating element is being checked.
E66	Failure of the heating element relay	The relay is checked and replaced; Circuit integrity monitoring is required.
E68	High leakage current	A general check of the integrity of the components of the washing machine, including the heating element, is carried out.
E71	Extreme resistance of the temperature sensor	The sensor and heating element are monitored for the presence of a short circuit to the housing; The electrical circuits are checked.
E74	Incorrect position of the temperature sensor	It is necessary to correct the position of the sensor;
E82	Inability to determine the position of the program selector	The electronic module and circuits are checked; The selector itself is checked.
E83	Selector read error	The code is displayed only in diagnostic mode. The electronic module needs to be checked and replaced.
E84	Recirculation pump recognition error	The electronic module needs to be checked and replaced.
E85	Failure of the recirculation pump, failure of the pump thyristor	The performance of the electronic module and pump is checked.
E91	No communication between electronic unit and user interface	The electronic module needs to be checked and replaced.
E92	No correspondence between the electronic unit and the user interface	The electronic module needs to be checked and replaced.
E93	Configuration error	The correct configuration code must be entered.
E94	Configuration and washing program error	It is necessary to replace the controller or overwrite the non-volatile memory.
E95	Communication error between non-volatile memory and processor	Requires checking the power supply of non-volatile memory; Checks the circuits between the EEPROM chip and the processor.
E96	Lack of configuration matching between the external elements of the controller and the controller itself	It is required to check the conformity of the configuration of external elements and the controller itself.
E97	Malfunction of the software of the controller and program selector	Machine configuration check required; The electronic module needs to be checked and replaced.
E98	There is no correspondence between the electronic module and the motor control unit	It is necessary to check and replace the electronic module; Circuit check required.
E99	Failure in the connection of the input / output electronics and the sound unit	It is necessary to check and replace the electronic module; Circuit check required.
E9A	Software failure between input/output electronics and sound unit	The electronic module needs to be checked and replaced.
EA1	DSP system failure	It is necessary to check and replace the electronic module; Checking the electrical wiring; The drive belt is being replaced; The DSP is being replaced.
EA2	DSP recognition error	The electronic module needs to be checked and replaced.
EA3	Motor drive pulley not fixed	It is necessary to check and replace the electronic module; Checking the electrical wiring; The drive belt is being replaced; The DSP is being replaced.
EA4	DSP failure	It is necessary to check and replace the electronic module; Checking the electrical wiring; The DSP is being replaced.
EA5	DSP thyristor failure	The electronic module needs to be checked and replaced.
EA6	No drum rotation signal received within 30 seconds	The drive belt needs to be replaced. Need to replace DSP; The drum is not closed (for vertical machines).
EB1	Mains frequency mismatch	The network settings need to be checked.
EB2	Mains voltage above the limit	The network settings need to be checked.
EB3	Mains voltage below the limit	The network settings need to be checked.
EBE	Safety relay failure	The electronic module needs to be checked and replaced.
EBF	Lack of protection circuit recognition	The electronic module needs to be checked and replaced.
EC1	Fill valve lock	Electrical circuits are checked; The operation of the electronic module is checked; The valve is checked.
EC2	Water transparency sensor error	Sensor check required.
EF1	Clogged filter or drain hose, long drain	Cleaning of the drain system and pump is required.
EF2	Clogged drain hose and filter, excess foam from the powder	It is required to clean the drain system and pump, adjust the amount of powder.
EF3	Water leakage, pump failure, pump power cable failure, AquaControl on	The cable or pump needs to be replaced.
EF4	No signal from water flow sensor, valves are open	No water or insufficient pressure.
EF5	Strong imbalance	Checking the amount of laundry is required.
EH1	Invalid mains frequency	Network check required.
EH2	High input voltage	Checking the electronic unit is required; The power supply needs to be checked.
EH3	Mains interference, low input voltage	Check and replacement of the electronic unit is required.
EHE	Protective circuit relay failure	The electronic module needs to be checked and replaced.
EHF	Protection circuit relay recognition error	The electronic module needs to be checked and replaced.

*If you did not find your mistake in the table, then write your question in the comments.

Looking at the errors of Electrolux washing machines, we can independently, without the help of a service center, determine the nature of the malfunction. Another thing is that many Electrolux error codes are displayed only in some cases, and the malfunctions themselves can be fixed exclusively at service centers. Also on our website you can find Samsung washing machine error codes.