Bosch washing machine errors

1. Check the operation of the sunroof lock. Make sure that nothing prevents it from closing normally.

1. Check the patency of the filter mesh at the entrance to the machine;
2. Check the water supply, check the pressure in the water in the water supply (low pressure can lead to an error);
3. Check the water supply to the washing machine.

1. We check the patency of drain hoses and sewers;
2. We check the performance of the drain pump - here the free play of the shaft is controlled, the resistance of the pump winding (approximately 200 Ohm);
3. In rare cases, the reason for displaying this code is a malfunction of the control module.

1. It is necessary to take measures to find the place of leakage;
2. The tightness of all connections is checked.

1. Check the loading door, try restarting the washing program.

1. If the inlet valve is closed, it should be opened;
2. Check inlet filter;
3. Check water pressure.

If after a certain time the water supply does not start, the current program will be reset, draining will begin.

1. It is necessary to make sure that the drain pump is working and clean it;
2. The water level sensor is faulty - you should make sure that it is working.

When this error occurs, the washing program is interrupted.

1. It is necessary to check the health of the heating element - if it is faulty, a replacement will be required;
2. The temperature sensor is faulty - you need to check it with a known good part;
3. The reason for the long heating may be a low voltage supply to the washing machine.

1. Check the operation of the heating element relay;
2. The water temperature sensor is checked - it may be faulty.

1. Malfunction of the control triac (triac);
2. Malfunction of the relay responsible for the reverse of the engine.

In the absence of successful attempts to start the engine, the machine enters the "Important malfunction" mode.

1. The sensor is checked or changed;
2. Circuit integrity is monitored.

Further operation of the washing machine is carried out without heating the water.

1. Aquastop is being checked;
2. The machine is checked for leaks;
3. The integrity of the electrical circuits of the Aquastop system is checked.

1. The quality of the incoming water is assessed - the operation of the sensor can cause its opacity;
2. The pressure switch is checked;
3. The sensor is cleaned from dirt and lime deposits;
4. The drain is checked for patency.

Further operation of the machine is carried out without rinsing.

1. The serviceability of the water pressure sensor (pressure switch) is checked;
2. The error is reset by turning the machine off / on, checking the integrity of the circuits leading to the sensor.

When this error occurs, the machine stops, indication and control are blocked.

1. The pressure switch is checked and adjusted;
2. The integrity of the circuits leading to the sensor is checked.

1. The integrity of the sensor circuits is monitored;
2. The correct operation of the sensor is checked.

1. The presence of water in the water supply is checked, the tap and water pressure are checked, the inlet filter is inspected;
2. Solenoid valves are checked;
3. The pressure switch is checked;
4. The aquastop system is checked.

1. Solenoid valves and pressure switch are checked;
2. The pump is checked;
3. Checking the filter, drain hose and pipe is required;
4. All electrical circuits associated with the above equipment are checked.

1. The electrical circuit leading to the hatch lock is being checked;
2. The correct operation of the mechanical part of the lock is checked;
3. After all checks are completed, the program is reset by turning the machine off/on.

If this indication is present, further program execution is blocked.

1. Triacs and relays controlling the lock are checked;
2. The electronic module is checked (the operation is performed at the service center).

Error F36 is critical, program execution is suspended.

1. The integrity of the circuits leading to the sensor is checked;
2. The correct operation of the sensor is checked.

1. The integrity of the circuits leading to the sensor is checked;
2. The correct operation of the sensor is checked.

1. The control triac is checked;
2. The control module is checked.

This malfunction is diagnosed in service centers, as it requires diagnostic and measuring equipment.

1. The tachogenerator is checked;
2. Possible malfunction of the control module;
3. Mechanical blocking is checked (linen chewing between the drum and the tank);

1. The control module is being checked, the relay or triacs may be faulty.

1. Control module;
2. The sensor itself
3. Electrical circuits.

The module firmware is being checked.

1. It is necessary to check the sensor and electrical circuits;
2. The input filter is checked.

1. Checking the mechanical and electrical parts of the door is required;
2. The control of electrical circuits leading to the door lock is carried out;
3. The machine is reset by turning it off/on.

1. The control module is being tested

1. The power is turned off for 15-20 minutes;
2. The module is checked and the software is replaced.

1. The integrity of the motor is monitored, if required, it is carried out washing machine motor repair;
2. The control module and electrical circuits are checked.