Why the washing machine does not drain water

Problems with the washing machine sooner or later arise for all users. Programs stop working for someone, and someone cannot cope with problems with draining. By the way, the last problem is the most relevant for many owners of automatic washing machines. Unable to cope with the removal of water or start the pump, the machines show an error and turn off.

This malfunction can manifest itself for a variety of reasons, which will be discussed in this review. Here we will look at how such breakdowns occur, what is their cause and how to do without calling the wizard.

We also note that due to the lack of water drainage in the washing machine, your washing machine door may not open. If you are also facing this problem, then all ways to unlock the door in the washing machine find this link.

Reset program

If the washing machine suddenly stops working at the stage of the last or intermediate spin, you should interrupt the program, and then try to start the machine from the same moment - for this pull it out of the socket.

If it didn't help, interrupt the program with the buttons and try start the "Rinse + Spin" program (usually the shortest program).If it does not help, you will have to "dig deep".

Replacing the electronic module

Software failures can be caused by incorrect operation of the electronics. It is impossible to do anything here without the appropriate knowledge and skills - the washing machine will have to be taken for repair. Here it will be checked and a complex of repair and restoration work will be carried out. In some cases a complete replacement of the electronic module may be required - the specialists of the service center will figure it out.

Drain does not work - check the filter

If the washing machine does not drain the water, you should deal with the filter. To do this, drain the water and unscrew the filter, by opening the door at the lower front of the machine. Here care should be taken not to flood the floor in the bathroom and not to flood the neighbors from below (if any).

A drain hose is located next to the filter - removing the cap from it, you can carefully drain all the water. Next, unscrew the filter and look inside. Here you can find anything from coins to clothing details. By the way, coins are the real enemy of filters, as they are able to completely block the duct. After cleaning the filter and removing the accumulated debris from there, you can try to start the machine for spinning. If nothing helps, you need to understand further.

Draining water from the tank don't you dare open the hatch - the flow of water from the tank will lead to a real flood. To empty the tank, use the drain hose located next to the filter.

The drain in the washing machine is broken - check the drain hose

A drain hose can be an equally good reason for the lack of a normal drain. First of all, you need to check its patency - for this you just need to blow into it, making sure by the sound that the air reaches the tank of the car.

Also follows check status siphon, it is quite possible that it is clogged with lint, threads, hair and other contaminants. A common cause of a non-working drain is the simplest drain hose bend - check its condition and make sure that it has a normal clearance. If not, and a large plaque has formed in the tube, then change the hose. Is the hose okay? In this case, you need to make sure that the pump is working.

Checking pump performance

The pump can give itself away in the first minutes of a malfunction. If she makes strange sounds, then it is quite possible that she just clogged with threads and pile. This happens with machines that have been in operation for many years.

The easiest way to diagnose is to listen to the sounds coming from the bowels of the washing machine. If you hear a quiet hum, then this may mean that:

• The pump is clogged and does not rotate;
• The pump motor is broken.

If nothing is heard at all, then this can mean the same thing. If there are suspicions that the pump is not working correctly, it is necessary to disassemble and inspect it. If threads are wound around the shaft and it is almost impossible to turn it, you should cleanse it of impurities, assemble and test the pump again.

Do you have a multimeter at home? Then you can see if the pump is receiving voltage (when the program starts and the drain is supposed to start) - but it is better to entrust such a test to specialists.

What to do if the pump is clean? You can try replace it with a similar model, having previously agreed with the seller on the return. By the way, if the pump is about to fail, then it will "warn" about this through numerous failures. If you get tired of constantly dealing with the lack of a drain, feel free to change it!

Checking the integrity of the wires

As already mentioned, when diagnosing a drain, you can check for the presence of supply voltage at the pump. If it does not, then there can be two problems:

• Electronics not working
• There were problems with the integrity of the wires.

If you can deal with the wires yourself, then the repair of electronics should be entrusted to the specialists of the service center.

Preventive filter cleaning and smart washing machine diagnostics

By the way, professional cleaning of filters can be performed even on a warranty washing machine. As for deeper interventions, they should be handled by a specialist service center or repair shop.

It should also be noted that some machines have diagnostic tools. First of all, this applies to LG washing machines equipped with Smart Diagnosis. Here, diagnostics is performed by calling the support service and activating the service information transmission function (reminiscent of the sound of a fax machine).

In addition, you can install a special diagnostic utility on your tablet or smartphone, and then run Smart Diagnosis. The washing machine will make a series of sounds, after which information about the causes of the breakdown will appear on the screen of the smartphone or tablet. The most advanced models are supplied NFC modulewhich greatly simplifies the diagnostic process.

Do you want to buy such a “smart” super-washer or pick up another new washing machine? Read modern rating of washing machines on our website!

What to do if the washing machine does not drain water?

If the washing machine does not drain the water, there is no need to panic and calculate the losses from the upcoming repair. It is likely that you can deal with the problem yourself.

The most complex unit in a modern washing machine is the electronic module. It is very difficult to repair it at home, and every man who knows how to handle tools can deal with a broken pump. Well, even a housewife can handle checking filters and drain hoses.