Sintepon is the most popular filler for outerwear. Caring for such things is not difficult, you just need to follow certain rules. If the jacket or coat is washed incorrectly, then the filler is knocked off in pieces and no longer normally performs its function. What to do in this case, is it possible to straighten the padding polyester in the jacket after washing, or can such a thing be put in the trash? You can solve this problem in different ways, which one to choose, the hostess determines herself.
How to prevent filler from knocking down
In order for the filler not to go astray, it is necessary to wash outerwear correctly. Hand washing is considered the most delicate, in this case the jacket can be laid out on the bottom of the bathtub and gently rubbed with a soft brush, then rinsed and dried in a horizontal position.
If outerwear is washed in a washing machine, then you should follow these recommendations:
- It is necessary to study the label, which is sewn to the wrong side of the product, well. The manufacturer usually indicates all the necessary information there.
- Jackets should be washed in the delicate wash mode, the water should not be higher than 40 degrees. Twisted such things at minimum speed.
- Dry coats and jackets in a horizontal position, periodically shake things up.
If, after pulling out of the machine, areas of the stray filler are noticeable, you need to carefully straighten it with your hands. This painstaking work requires caution, but the result is worth it.After straightening the synthetic winterizer, the jacket is shaken well.
Extra wash
You can even out the synthetic winterizer that has fallen into lumps by resorting to repeated washing in the machine. For such a wash, you need to prepare three new tennis balls or special rubber balls that are used to wash down jackets. In order for the synthetic winterizer to fluff up, the jacket should be washed according to the following algorithm:
- Outerwear with fallen filler is placed in the drum of the washing machine along with tennis balls.
- Set the most delicate mode, you can not add detergent.
- Turn on the machine and wait for the end of the cycle. In this case, the balls evenly distribute the filler throughout the product.
- After turning off the machine, the jacket or coat is taken out of the drum, shaken well and placed to dry on a horizontal surface.
In order not to lose the synthetic winterizer in the jacket after washing, it must be properly dried. To do this, the thing is laid out on a dryer or table, after laying a sheet folded in half. In the process of drying, the product is periodically shaken so that the synthetic winterizer is evenly distributed. If some areas have fallen off, they need to be carefully distributed with your hands and then dry the thing.
A vacuum cleaner will help
An ordinary household vacuum cleaner will also help to quickly beat the synthetic winterizer.If the synthetic winterizer is badly lost in outerwear, then it is not necessary to be sad over the damaged thing. Using an ordinary vacuum cleaner, you can solve the problem in a few minutes. Restoration of things is carried out in the following sequence:
- After washing, the jacket is laid out on a flat surface and assessed in which places the filler has gone astray.
- Next, they take a vacuum cleaner, set the average suction mode and all the problem areas go through the tube without a brush. In order for the synthetic winterizer to evenly spread over outerwear, it is worth vacuuming the entire thing, paying special attention to the sleeves, collar and pocket area.
- When all the fallen filler is straightened, the thing is left to dry on a horizontal surface.
Using a vacuum cleaner, you can level the synthetic winterizer even after the product has completely dried. To do this, you can vacuum the outerwear several times, and shake the jacket well in between.
It is desirable to pass outer clothing with a vacuum cleaner over a layer of cotton fabric. This will help prevent contamination.
Carpet beater
Not bad breaks the matted pieces of synthetic winterizer and a carpet beater. If there is no such device in the house, then you can use an ordinary stick. In this case, you need to restore the previous appearance of the thing, adhering to the same rules:
- A jacket or coat is hung on hangers, which are then attached to a rope.
- The thing is fastened with all zippers and buttons so that it does not deform during the knocking out process.
- Then they begin to carefully knock out the jacket, evenly tapping all parts of the product. Continue the procedure until the stray filler remains.
With the help of a beater, you can more evenly distribute the synthetic winterizer, which often falls to one side during wear.
If nothing helped
If all the suggested methods did not help to solve the problem, do not be upset. You can resort to the least, which will take a lot of time, but it will definitely return the jacket to its original appearance.
To do this, it is necessary to determine in which part of the thing the synthetic winterizer crumpled the most.Next, the lining is torn off and the filler is straightened with your hands, then it is fixed in several places with a needle and thread. After the entire synthetic winterizer is straightened evenly, the lining is sewn again.
In the event that it is not possible to straighten the filler on your own, you should contact a professional seamstress. She will be able to replace the filler with a new one and this service will cost less than a new jacket. After that, it is very important to wash the outer things correctly so that the filler does not crumple again.
