Whirlpool washing machine error codes

If the iron breaks at home, then it is unlikely that he will be able to tell his owner about the nature of the breakdown. Washing machines are another matter - they are equipped with self-diagnostic systems that indicate all malfunctions.

Looking at the Whirlpool washing machine error codes presented in a table, we will be able to quickly bring the machine back to life - many breakdowns are easily fixed at home.

Similarly, you can find out Kandy washing machine error codes on our website.

Whirlpool washing machine fault codes are displayed on the control modules - on the scoreboard, where we see the time until the end of the wash. To find out the malfunction, you need to read the code and check the table.

The code	Description of the problem	Possible causes
F01 or FH	Malfunction in the water inlet system (low level or no inlet)	Water pressure check required; The filters are cleaned, the position of the hose is adjusted; It is required to check the water level sensor, solenoid valve, pressure switch and drain pump; The controller is checked.
F02 or FA	AquaStop worked	Solenoid valves and controller are checked; The tightness of the components of the washing machine is checked.
F03 or FP	No water drain	The drain pump and its electrical circuits are checked; The patency of the drain system is checked; The functionality of the controller is checked.
F04	Slow water heating or no heating at all	The temperature sensor and its electrical circuits are checked; The heating element is checked and cleaned from scale.
F05	Temperature sensor not working	The sensor and its electrical circuits are checked.
F06	There is no signal from the tachogenerator, there is no rotation of the engine or it rotates at low speeds	The correct position of the tachogenerator coil is checked; The connection between the tachogenerator and the engine is checked.
F07	Engine control circuit malfunction	It is required to check and replace the control triac; The controller is being repaired or replaced;
F08	Breakdown of the heating element	The heating element circuits and the heating element itself are checked; The protective pressure switch is checked; Temperature sensor check required; The functionality of the controller is checked.
F09	High water level in the tank	It is required to check the operation of the pressure switch; The solenoid valve is checked (it may jam in the open state); Controller verification required.
F10	The engine does not turn	The thermosensor and the engine control unit are checked; The control triac is checked on the controller board.
F11	Communication failure	It is required to check the compliance of the mains parameters.
F12	There is no water heating in the tank	The performance of the controller is checked; The heater, protective pressure switch, contact groups and electrical circuits are checked; The performance of the temperature sensor is monitored.
F13	Water does not enter the tank or flows very slowly	The water pressure is monitored, the condition of the taps is checked; The patency of the tray for washing powder is checked; The mesh filter is being cleaned.
F14	Errors in the control system (erroneous data from EEPROM)	Checking and flashing the EEPROM on the controller board is required.
F15	Motor failure	The reverse relay and the control triac are checked; The contact groups of the engine and the engine itself are checked; Checking electrical circuits; It is required to check the position of the tachogenerator or replace it; Checking the washing machine controller.
F16	Control system failure or failure	The controller is tested and the electrical circuits are tested.
F18 or Fod	Bad washing powder (programs blocked)	The washing powder needs to be replaced or the dose adjusted.
F19	Incorrect operation of the power system, the machine does not start or an unexpected stop occurs	Power line parameters need to be checked.
F20	Controller failure - non-execution of commands	It is required to check the functionality of the controller, but before that, a test restart of the washing program is performed.
F21	Controller failure	All electrical circuits between the controller and the control module are checked; The controller is being replaced.
F22	Water does not flow through the detergent drawer. No water heating.	It is required to check the heating element and its electrical circuits; The parameters of the supply network are monitored.
F23	Simultaneous signals "tank empty" and "tank full" from the water filling system	The pressure switch is checked and replaced.
F24	Long (more than 60 sec) tank overflow signal	The pressure switch is checked and replaced.
F26	The engine has stopped spinning	The control triac and current-carrying tracks are checked and replaced (in case of damage).
F27	Motor only rotates in one direction	Reverse relay failure - needs to be replaced.
F28	After any washing cycle, the motor rotates slowly or does not start at all	Breakage of the relay for switching the stator windings, it needs to be replaced.
F31	Internet software update failure	Internet access required.
FDL	Hatch lock failure	The operability of the lock and its electrical circuits is checked; If it breaks down, it will be replaced.
FDU	Lack of closing of the loading hatch	It is necessary to close the hatch more tightly; The hatch lock is being checked.

Whirlpool washing machine errors make it much easier to diagnose and repair equipment - this is a great help for repair professionals. On our website you can also find Ariston washing machine error codes and Daewoo washing machine error codes.